Articles
   
       
       
Pics/Video
   
       
       
Shop
Search
 
 
 
 
 
Home   Articles   Pics/Video   Gear   Wake 101   Events   Community   Forums   Classifieds   Contests   Shop   Search
WAKE WORLD HOME
Email Password
Go Back   WakeWorld > >> Boats, Accessories & Tow Vehicles Archive > Archive through August 27, 2003

Share 
Reply
 
Thread Tools Display Modes
Old    Matt (pierce_bronkite)      Join Date: Jul 2003       08-26-2003, 2:39 PM Reply   
Can someone provide me with any advice on amp placement in my boat? I have a Tige 23v and was just wondering where most people install them?

Also is there any thing that I need to be aware of? Moisture, Heat, etc?

Old    whitechocolate            08-26-2003, 2:54 PM Reply   
Im not familiar, with The Tige. But In my Nautique. I mounted them On the hull. The amps are mounted on boards that are glued to the side of the boat Up under the gunnel where things stay dry.
Old    whitechocolate            08-26-2003, 3:02 PM Reply   
Woops try this
This is the Amp Board

This is the Amp mounted to the board

This is the amp with the side pannel on


This is as exposed as my amps get the Amps on the Passenger side are tucked way up under the gunnel and are out of view. But this amp on the drivers side is very large so I only had a few places it wolud mount.
Old    A. P. (bigdad)      Join Date: Apr 2002       08-27-2003, 1:18 AM Reply   
I guess I'm different than other people. I spent quite a bit of money getting quality amps and wires and hooked up an amp board that looks real nice. I intended putting it in a location that I could display them but I ended up putting the amp board in a location behind the bow seats. It is out of the way and I figure if someone tries to steal them from my boat they would have a heck of time finding them. Consequently it made adjusting the inputs and frequencies a pain.
Old    Timothy (timmy)      Join Date: Jul 2001       08-27-2003, 3:43 AM Reply   
I put mine in the storage compartment on the spotter side, and fastened an amp rack board to that wall with bolts. this required drilling holes in that panel and temporarily removing some of the bow seat pads but it made for a really nice and out of the way mounting scheme.

here is a photo before I upgraded the sub amp to 4 ga and tidy'd up the wires a bit.

hgj
Old    hockeyruss            08-27-2003, 6:05 AM Reply   
I am with Tim on this one!
Old    hyperryd            08-27-2003, 6:20 AM Reply   
I welded a square tubing rack and then powdercoated it and installed the amps behind the observer seat. The bottom amp is about 5/8" off of the floor just in case the carpet got a little wet.
The wall isn't small, the amps are large.



(Message edited by hyperryd on August 27, 2003)
Old    Matt (pierce_bronkite)      Join Date: Jul 2003       08-27-2003, 7:06 AM Reply   
Thanks for the input! Going to install mine today.
Old    TY-one-on (typhoon)      Join Date: Jul 2001       08-27-2003, 7:09 AM Reply   

under the observers seat
Old    matt moss (mossy44)      Join Date: Oct 2001       08-27-2003, 9:06 AM Reply   
tim (and others) if the wall is thick enough to mount your amp board with those bolts, why not just mount the amp with 4 screws? whats the advantage to an amp board?

right now, i have mine mounted under the observer seat on the right side wall. i did not make a board though. (xstar)
Old    whitechocolate            08-27-2003, 9:19 AM Reply   
"John" Very Nice: what Orions are they??

Hey A.P.(Big Daddy) What do you mean your diffrent from other people? You spent money on Quality Amp's? (like no one else here did). Why is it that you were the only one that didn't post a photo of your system or offer any helpfull advise? In not trying to be a Dick did I read your post wrong?
Old    whitechocolate            08-27-2003, 9:29 AM Reply   
I know with most boats storage is a issue. When mouting Amp's I would use this advice as your way of deciding where you mount.
#1 Does it stay dry as possable there? I know this is a hard place to find on a boat (The amps draw in mositure as they heet and cool) it's no good mounting some where its dry and then you your throwing wet life jackets there. The amps suck in the moisture. So sometimes a place where they are more vented works beter.
#2 Where they fit.
#3 where you can adjust them. where my amps are installed it is a whore to adjust anything.If this is the same for you. Make the wires long enough so you can take the amps down with all the wires connected and then adjust away and then mount them back.
Old    toddkerschbaumer (tktige)      Join Date: Aug 2003       08-27-2003, 12:35 PM Reply   
Tim, Wakenup,
Nice job on the install they both look great. I am thinking of doing the same on my 2001 21v. I have the factory amp in the front compartment below the glove box and hate it. I want to install a second 400 watt amp for the Tower speakers and run the sub on the factory putting both in the back storage comp battery side. Did both of you run a second battery? If so, how did you hook this up with an Isolator or just a perko switch and where can you find a daul battery switch that is the same size as my cuurent switch (size wise)? All the dual switches I have seen are massive and look terrable installed.

Thanks TK
Old    salty87 (salty87)      Join Date: Jul 2002       08-27-2003, 1:29 PM Reply   
matt-

a mounting board lets you run/hide the wires behind the board for a cleaner look. a mounting board can also turn a weird angle in the hull into something you can secure an amp to. you don't really want to secure to the hull wall without a board...unless its way above the waterline. haha

i mounted 1 amp to a board and another to the back of a bow seat without a board.
Old    Matt (pierce_bronkite)      Join Date: Jul 2003       08-27-2003, 1:59 PM Reply   
Thanks for the input Grant, and everyone. Also, do any of you un-install the amps over the winter?
Old    Timothy (timmy)      Join Date: Jul 2001       08-27-2003, 2:24 PM Reply   
matt, i used a board because screws and fiberglass generally don't do well together unless they are really long and going into a lot of glass. the board i used was actually my old kick panel for the driver's feet (resized) so it is some sort of plastic. this way i could use some nice pan head screws to mount the amps to the board, and also not worry about making multiple holes. i originally set it up to hide the wires but when it came down to it I decided otherwise.

todd,
i currently only have one battery. i am only running 700W and don't run the stereo with the boat off. however, when I graduate and have cash flow again I will upgrade and add a battery or two, with an isolator.

also i agree with grant, putting wet stuff in by the amps is not a great idea. my storage area is dry storage only.
Old    hyperryd            08-27-2003, 6:13 PM Reply   
Grant: There are two 8002's and one 8004. I should have the system done by this Friday. I'll post more pics later.
Old    Darren Yearsley (ralph)      Join Date: Apr 2002       08-27-2003, 6:43 PM Reply   
Wow, those amps are outstanding John, good work.

Reply
Share 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On



All times are GMT -7. The time now is 9:58 AM.

Home   Articles   Pics/Video   Gear   Wake 101   Events   Community   Forums   Classifieds   Contests   Shop   Search
Wake World Home

 

© 2012 eWake, Inc.    
Advertise    |    Contact    |    Terms of Use    |    Privacy Policy    |    Report Abuse    |    Conduct    |    About Us