Wake 101
Home   Articles   Pics/Video   Gear   Wake 101   Events   Community   Forums   Classifieds   Contests   Shop   Search
WakeWorld Home
Email Password
Go Back   WakeWorld > Wakesurfing

Thread Tools Display Modes
Old     (ReSession)      Join Date: Apr 2010       09-01-2011, 9:55 AM Reply   
I've been holding off posting pics cause as I knew as soon as I did everyone would want to see how the wave looked...I'm 6.5 hours away from breaking the engine in, and if I take the day off tomorrow we should be surfing by mid-day Friday or Saturday if I get stuck working! With that said, here's a few of the pics.

Let me just say, this boat is HUGE! The width, the gunwale'll see from the pic that you can fit your entire fist under the platform and it's still not touching the water, versus my old boat that was sitting way lower. We tossed a few people on the rear sundeck for fun and the wave looked pretty damn nice and I'm really excited to see what the stock 1100 lb system plus the 1000 lb surf sac and the 400lbs of lead sacs (8 of them x 50lbs). The boat comes stock with 5 plumbed tsunami I had them add 1 Jabsco pump and the cool thing is that I have enough hose where I can just run them to the other (starboard) side and fill the same sack over there with the Jabsco (I'll just cap off the top instead of venting it like I have set up for the port side).

Looking forward to sharing some wave & surf pics this weekend...until then, still breakin' her in!

Attached Images
Old     (ReSession)      Join Date: Apr 2010       09-01-2011, 9:59 AM Reply   
You'll see an Inland Surfer production Flyboy and a prototype Flyboy we're testing for the Walkers in the racks too...these are KILLER boards! The IS Flyboy is super-defined and you may have read my previous review in this forum, whereas the prototype Flyboy has softer edges and a bit bigger buddies (215-220 lbs) really like this board! More to come guys!
Old     (dreamer)      Join Date: Nov 2008       09-01-2011, 10:49 AM Reply   
With your platform up high like that will there be more wash on the surf wave?
Old     (ReSession)      Join Date: Apr 2010       09-01-2011, 10:55 AM Reply   
JS - doubtful...I've rode behind other V226's with the same platform/ the time it's all weighted down, the platform will be much closer to the water. The platform is also trimmed on the sides to prevent drag and is NOT huge! Here's a pic of the top view!
Attached Images
Old     (surfdad)      Join Date: Sep 2004       09-01-2011, 12:34 PM Reply   
Nice looking boat and boards too!
Old     (ragboy)      Join Date: Aug 2007       09-01-2011, 2:20 PM Reply   
That new tower is such an improvement, looks great. The older towers just seemed cheaply made. Nice colors.
Old     (johnboyy7)      Join Date: Apr 2011       09-01-2011, 2:42 PM Reply   
nice looking ride and boards. not a bad set up.
Old     (ragboy)      Join Date: Aug 2007       09-01-2011, 3:13 PM Reply   
I just noticed, are you really towing it with that, is that a VW?
Old     (wakeandsnow27)      Join Date: Jun 2004       09-01-2011, 4:23 PM Reply   
Originally Posted by ragboy View Post
I just noticed, are you really towing it with that, is that a VW?
touaregs and cayennes can have a substantial amount of towing capacity than people would think.
Old     (ragboy)      Join Date: Aug 2007       09-01-2011, 4:36 PM Reply   
Pretty cool, thats a lot of boat.
Old     (getssum)      Join Date: Jul 2005       09-01-2011, 5:54 PM Reply   
The boat's going to eat the t-reg!
Old     (Nova)      Join Date: Jul 2011       09-01-2011, 8:41 PM Reply   
Looks great! Hopefully I see you out there on good 'ol Champlain.
Old     (ReSession)      Join Date: Apr 2010       09-02-2011, 6:43 AM Reply   
Robert - it's a 2008 Touareg II V8, rated to tow up to 7700 lbs! I pulled it back from Albany (300 miles) last Friday with 400 lbs of lead in the rear lockers averaging 70-75 mph and the majority of the time, I forgot it was there (with the exception of a huge picklefork in my rear view mirror!). The T2 is a SWEET machine and even has the air suspension to automatically adjust for the weight. It also has differential locks, which actually helped me from getting stuck on a muddy/clay launch the other week!

The V10 Touareg pulled a 155 ton Boeing 747 from a standing pull (filled with 4.2 TONS of ballast!) and double the tire pressure...check out the Fifth Gear vid here!

Mike, heading out on the lake shortly...took the day off to complete my final 5 hours of break-in, and possibly surf it up this evening!

*sorry I posted this in the wrong section!
Old     (ragboy)      Join Date: Aug 2007       09-02-2011, 8:25 AM Reply   
Wow, pretty amazing. I have an Audi and love it, but didn't know the Touareg could do that.
Old     (ReSession)      Join Date: Apr 2010       09-03-2011, 7:26 AM Reply   
Damn, nothing better than doing a Summer's worth of research on boats, having it delivered last week, and cranking out a SICK wave my first attempt!!! I really can't be happier/excited/proud with my new wave...and it's only going to get better!

The stock tanks filled up in literally 3-4 minutes...and I'm waiting on a few connections from Wakemakers before I have the 1000 lb sac fully plumbed, so I filled it manually in about 10 minutes with a tsunami.

The GREATEST thing I love about this boat & wave is NO sacs on the seats! What a difference! Trim tab holds the bow down and shapes up the wave SOOO nice...there is no platform drag, no prop wash...just a damn-near perfect wave! It's incredibly long and I was overshooting all my spins because I was gaining so much speed! And definitely landing my biggest airs...the V226 + Inland Surfer Flyboy = a killer combination!

Now...the pics & vid don't do it enough justice because this is our FIRST run filled up, heading to go meet 4 buddies on their Malibu and have them jump in with there's only myself and 1 passenger! Waiting for a few iPhone videos to be emailed to me...until then, here's what it's looking like!

YouTube Video of new wave

Also, I didn't even notice when I first checked it out, but the guys @ Semper Speed & Marine machined in some extra bracing to support the engine wall, so I included a pic of that as well!

Headed out again today...definitely will get some wakesurfing vids!
Attached Images
Old     (dbdan)      Join Date: Jun 2009       09-03-2011, 8:38 AM Reply   
You live in Vermont and bought it from Semper?!?!?!
Old     (inland_surfer)      Join Date: Aug 2002       09-03-2011, 8:38 AM Reply   
wow nice ride - thanks for the pics of the fly boy too !
Old     (ReSession)      Join Date: Apr 2010       09-03-2011, 9:28 AM Reply   
Dbdan - that's how I roll

JF - thanks, hitting up the lake now for a surf session and hope to get some good pics and vids riding the Fly's so sweet!
Old     (ragboy)      Join Date: Aug 2007       09-03-2011, 1:50 PM Reply   
Those braces are great, nice touch by the dealer.
Old     (TheSqueakyWheel)      Join Date: Oct 2010       09-04-2011, 6:15 AM Reply   
Sweet boat. Awesome job on the divider brace - that's far more elegant than the u-channel I used.

Also, having spent a good deal of time on the new MBs I have to comment that the v226 shares many similarities to the new MB. They both appear to have a similar deep-v hull, the high swimplatform and spacious wide beam interiors. And both throw killer waves.

From the new MB catalog....
Attached Images

Last edited by TheSqueakyWheel; 09-04-2011 at 6:19 AM.
Old     (ragboy)      Join Date: Aug 2007       09-04-2011, 2:52 PM Reply   
Yes, CMS has a 23LSV (used) on showroom floor with the V226, and it is evident why malibu needs a lot of weight to get it over. Thats a nice shot of the rear end of the MB.
Old     (ReSession)      Join Date: Apr 2010       09-05-2011, 6:51 AM Reply   
Looks like we picked the 2 best days to surf the new boat, as the rain is coming down in VT this morning! The past few days have been super WINDY (10-15mph out of the South!)...if you don't have the Windfinder app for your iPhone, I highly recommend it! Combine that with the 'next 6 hours' for the Weather-in-Motion map on and you're your OWN weatherman!

*First off...I don't recommend this, as it's highly illegal in most/all states! BUT...since I knew the cop's boat was docked up @ the marina and there was no chance of seeing him on the lake, I decided to pull my girlfriend SOLO behind the V226 while waiting for my buddy to rig up a few sails for his friends to go off and sail his pair of Lazers (yes, it was THAT windy!).

You'll see from this video that there's no one in the boat with me. I have the stock center (600 lbs), the stock port (250 lbs), the 1000 lb port locker sac, and 400 lbs of lead on the port side under the my 165lbs! So JUST over a ton of ballast...and the wave was so fun! We played around with filling the starboard stock tank as well...I liked it empty, gave a more gradual wave...where my GF liked it full, with a more peaked wave.

We then picked up 4 more riders/passengers and the wave took a turn towards amazingness! As Jeff Walker was explaining to me, this boat LOVES weight...the more, the merrier! Pretty sure I'll have some custom sacs designed over the winter and added for the Spring. I timed the fill process and it was JUST under 7 minutes, even without the 1000 lb sac plumbed in the back (waiting on a few elbow connections to be delivered!).

In any case, here's a few'll see the wave has zero prop wash, zero platform drag...just a perfect "marbled" wave forming nice and long! In the pic where I'm way back in the wave, I had no problem pumping back in! My buddy PG is getting pretty decent at riding goofy and starting to show some fin as well!

A quick vid of me riding the prototype Fly boy from Jeff Walker GoPro fell off my extendable pole and 86'd to the bottom of the lake (43' down in murky dark water!) so I'm stuck on the iPhone vids for the time being
Attached Images
Old     (jdhart73)      Join Date: Mar 2010       09-05-2011, 8:31 PM Reply   
Awesome wave. Any solution to the crazy loud pipes that seem to stay above the water while under way, FAE?
Old     (ReSession)      Join Date: Apr 2010       09-06-2011, 9:56 AM Reply   
Jake - thanks man! Yeah, I'm probably going to look at a few options...most V226's have the down-turned exhaust pipes on them but mine didn't for some reason? Just checked out the FAE site, I'll have to see if they offer them for my boat because they don't have the V226 listed as an option under Ski Supreme. I shot them an email to find out. For now, I'll just have to crank the tunes!
Old     (duffymahoney)      Join Date: Sep 2008       09-06-2011, 10:08 AM Reply   
I tried the downturned pipes on my avalanche. They didn't work at all. Just put an FAE on it. Larry over at FAE should be able to hook you up easily. Nice looking wave.
Old     (ragboy)      Join Date: Aug 2007       09-06-2011, 1:40 PM Reply   
Good looking wave. Lots of fun dialing in a new boat.
Old     (wakebrdjay)      Join Date: Apr 2008       09-06-2011, 5:13 PM Reply   
Greg there's a form Larry has that you use to take various measurements and he can make one to fit.He didn't have the V212 when I got mine.Took the measurements and sent them to him and he made one and it worked perfect.Been using it 4 seasons now not one problem.
Attached Images
Old     (TheSqueakyWheel)      Join Date: Oct 2010       09-08-2011, 3:49 PM Reply   
see PM I sent please. I have a 2012 v226 demo lined up for this weekend and could use some advice on proper ballast setup.
Old     (ragboy)      Join Date: Aug 2007       09-08-2011, 4:00 PM Reply   
Just FYI, Grant has a 2011 for sale for $56.5K, and its in amazing condition. Its new, but was used for demo, the wake is documented in the West Coast Open videos. The thing is, it will make a better wake than the boats above. For some reason supreme started rasing the swim decks up, and it hurts the goofy wake especially. Grants boat has the deck down where it needs to be, and also makes it normal to get in and out of the boat.

Before you get one make sure the deck isn't raised up like that, at least that is my advice to you. Dennis has surfed behind both sides of the supreme on boats with decks up and down, he can provide more info if you want to PM him. Also, he did tell me the higher deck is a lot harder to get back in.

Anyway, I was out 2 weeks ago visiting CMS and took pics, the boat is immaculate from what I could see and has that killer stereo upgrade that special bimini that you can load boards and tubes and whatever on.

Old     (ragboy)      Join Date: Aug 2007       09-08-2011, 4:01 PM Reply   
If embed doesn't work, here is a link.
Old     (ragboy)      Join Date: Aug 2007       09-08-2011, 4:16 PM Reply   
Here is the only picture I have of Grant's deck:

IMG_0412 by wake9, on Flickr
Old     (SteveO)      Join Date: May 2011       09-08-2011, 9:56 PM Reply   
Ragboy - That raised swim deck thing must have been on the 2011 models. I've got a brand new 2012 and my swim deck is not raised.

Old     (ragboy)      Join Date: Aug 2007       09-08-2011, 10:12 PM Reply   
Cool deal. Grants boat isn't raised, then some were, then back down I think. Because the 2012 one at the West Coast Open wasn't raised, so I thought that that was no longer an issue. But then I saw the pics of Greg's boat, and thought maybe they stuck with that, which I think would have been a mistake.

Cool deal, great looking boat. Those new towers look so much nicer. Congrats.
Old     (dennish)      Join Date: May 2005       09-08-2011, 10:26 PM Reply   
Greg's boat was made when they thought that the raised swim deck was the answer. I think they now understand that it is not much help at all.
Old     (ReSession)      Join Date: Apr 2010       09-11-2011, 8:25 AM Reply   
SteveO - nice looking boat, you surf it yet??

I haven't rode the dark side yet but so far, I have had no issues/complaints about the wave! I'm going to get some videos of me riding behind the boat today and show you some shots of how JUST the left corner of the platform dribbles in the thought is that IF the platform were 4-6" lower, you'll get some MAJOR drag of the platform to the point of it affecting the wave (whether it's positive or negative...that's to be determined?). I'm just going off what I'm seeing from how far my boat sits in the water. So I'm curious to know/see how the wave is behind the 2012 with the lower platform, based on how we're weighting/riding the V226? Perhaps it will be better for the goofy side wave - post some pics/vids?

Check out the videos from yesterday...the 'dribble' I mentioned can be seen coming off the platform. Can anyone explain how the wave will be BETTER if you sink the platform 4-6"???

As far as getting out of the water...I'm up and onto the platform in half a second but I'm sure the bigger you are, the harder the forces of gravity work against you! It's not like you need a ladder or someone to pull you up from the boat like my dad used to when I was a kid The girls have complained at the fact it's harder to pee off the back though!

Seems like the V226s have been changing/progressing pretty quickly, like the updated dash or the tower...2 of the reasons I did not like the 2010's or some of the first 2011's! Hopefully they update their website and facebook mom has more friends!
Attached Images
Old     (ragboy)      Join Date: Aug 2007       09-11-2011, 11:23 AM Reply   
Originally Posted by ReSession View Post
Check out the videos from yesterday...the 'dribble' I mentioned can be seen coming off the platform. Can anyone explain how the wave will be BETTER if you sink the platform 4-6"???
Well, if it was better, supreme probably would have left the deck up there, but try the goofy side. When the deck is up higher it doesn't knock down the prop wash on the goofy side, doesn't affect the regular much if at all. So if it doesn't bother you, than sounds all good. I can just be a bit "goofy" sensitive. ;-)
Old     (wakebrdjay)      Join Date: Apr 2008       09-11-2011, 1:37 PM Reply   
I'll be willing to bet the goofy side is cleaner.
Old     (jdhart73)      Join Date: Mar 2010       09-11-2011, 10:41 PM Reply   
I will head out with Steve sometime this week and hopefully we can test his goofy wave as I am the only one that surfs it!
Old     (ReSession)      Join Date: Apr 2010       09-12-2011, 7:09 PM Reply   
Cool, that makes sense Robert! I need to check it out myself and see what it's like...maybe we can try this weekend? An adjustable-height swim platform would be a sweet option, to let you adjust the prop wash, etc!

Hopefully everyone gets the wave they're looking for with their V226's? I'd love the opportunity to test drive my boats before I buy them but all the dealers are all 4+ hours to the closest dealer that maybe has 1 mid-range model of 1 brand (like Nautique or Centurion) I have literally done ALL of my research online, along with the entire buying process and so far, the boat has far-exceeded my expectations right out the box!
Old     (SteveO)      Join Date: May 2011       09-13-2011, 12:29 AM Reply   
Your wave looks awesome. I wouldn't worry too much about your swim deck height. My swim deck is in the "normal" position and there is enough space between the prop wash and the swim deck, that I can see my trim tab while surfing.

What prop are you running? The clearance on my 2012 stock prop is only 5/8". I may have to stay with a 13.5" prop, like the Acme 1579 (13.5 x 14.24).
Old     (TheSqueakyWheel)      Join Date: Oct 2010       09-13-2011, 8:28 AM Reply   
Anyone know the "stock" prop on the 2012?

I demo'd a v226 this weekend with a stock prop. We had trouble maintaining speed around 11mph with an extra 1100 lbs of ballast, 3 adults, 5 kids. Also, the boat would decelerate terribly from 25 mph to 15mph when turning sharply, for example, while tubing.

The dealer and I both suspect it's the prop. he's going to reprop it with as low a pitch prop as he can. Any suggestions what works best at 5000' ?
Old     (SteveO)      Join Date: May 2011       09-13-2011, 9:30 AM Reply   
Our 2012 came with a 13.5 x 16 Acme 537. I know some guys are running the 1235 (14.5 x 14.25), but my 2012 does not have enough clearance to run that prop. I'm going with either a 1433 (14 x 14.24) or 1579 (13 x 14.25).
Old     (ReSession)      Join Date: Apr 2010       09-13-2011, 10:18 AM Reply   
I'll have to check my prop when I get a chance? In the meantime, I pulled the rear image of my boat/platform for comparison to the 2012...looks to be 2-3" difference? We'll see what kind of difference that makes on the goofy side vs. regular?
Attached Images
Old     (SteveO)      Join Date: May 2011       09-15-2011, 6:54 AM Reply   
We've decided to go with the Acme 1433 which is a 14"x14.25 prop. I've got about 3/8 to 7/16 clearance. I may end up with a little prop burn in the gelcoat, but the added performance is worth a little gel coat repair later.
Old     (TheSqueakyWheel)      Join Date: Oct 2010       09-15-2011, 7:43 AM Reply   
Thanks for the info. I'll pass it along to my dealer.
I was also told that Supreme is adding a switchblade option for 2012 !
Old     (joshljoshl)      Join Date: Jul 2000       11-03-2011, 6:28 PM Reply   
Originally Posted by SteveO View Post
We've decided to go with the Acme 1433 which is a 14"x14.25 prop. I've got about 3/8 to 7/16 clearance. I may end up with a little prop burn in the gelcoat, but the added performance is worth a little gel coat repair later.
Steve, have you had any time to try out the 1433? Was it a noticeable improvement? Any gelcoat rub? I just bought a 2011 V226 and it came with Acme 275 (13.5 x 17.5 and less cup) -- I'm anxious to switch it out, but it looks like it would be a tight fit!
Old     (SteveO)      Join Date: May 2011       11-03-2011, 11:32 PM Reply   
We got about 4-5 hours on the 1433 prop before we winterized. It is a noticeable improvement. There may be some gelcoat burn over time, but I don't see any yet. I only have about 3/8, maybe 7/16. That is one thing Supreme needs to improve......get enough clearance to run a 14.5" prop. I would love to run a 1435!
Old     (wakebrdjay)      Join Date: Apr 2008       11-04-2011, 8:51 AM Reply   
Is the 1435 a new size?I don't see it on Acme's list,or do you mean 1235?
Old     (SteveO)      Join Date: May 2011       11-15-2011, 7:13 PM Reply   
Yeah, 1235 sorry.
Old     (joshljoshl)      Join Date: Jul 2000       11-17-2011, 10:35 AM Reply   
For those interested - I installed the 1433 on my '11 V226 yesterday and took her for a test run. NIGHT AND DAY difference over the 13.5x17.5 that came with my boat. Immediately I noticed planing with much less throttle, albeit more RPM. The downside is now at 3000 RPM I am only doing about 23 MPH (27MPH for old prop), making for a longer, less efficient cruise to the flat water. I haven't loaded up the boat and tried surfing with the new prop yet, but I have no doubt that it will save gas and wear and tear with 3000+ extra lbs in the boat. I will do that comparison once it warms up and I can find 10 other people that want to be on the water. The taller prop will be saved for unloaded river cruising days, as it achieves a best of ~3.4 MPG at 25-27mph versus the new prop's best of ~3.2 MPG at 23-24mph.
Old     (dreamer)      Join Date: Nov 2008       11-17-2011, 12:33 PM Reply   
Ya, that's what I hate about my short pitched prop as well .Great for wakesurfing but sucks cruising and tubing my kids. I plan on trying the OJ 5 blade in the spring.
Old     (joshljoshl)      Join Date: Jul 2000       08-27-2012, 8:58 PM Reply   
Just an update on my earlier post about running the 1433. It went for several months with not a sign of wear on the gelcoat, but recently I noticed a black spot where it has worn through. You can actually see the fibers and porosity in the underlying glass. I'm hoping a quick fix with some epoxy (ding dough?) will fix her up. Any suggestions? I don't really care about the cosmetics in that location, just don't want it to get any worse. I just turned 135 hours and that's the only issue. I would still highly recommend this prop, especially if you run a ton+ of ballast on a regular basis!
Old     (duffymahoney)      Join Date: Sep 2008       08-28-2012, 9:59 AM Reply   
You can glue a small stainless plate above the prop. Acme suggested this to me.
Old     (SteveO)      Join Date: May 2011       08-28-2012, 7:54 PM Reply   
Yeah Josh, mine has done the exact same think. Duffy, what glue would hold good?
Old     (duffymahoney)      Join Date: Sep 2008       08-28-2012, 8:15 PM Reply   
Gosh I don't know. Something you could remove but still is strong.
Old     (wakebrdjay)      Join Date: Apr 2008       08-28-2012, 9:00 PM Reply   
I have a good idea on how to do this.Is the spot above the prop flat?
Old     (SteveO)      Join Date: May 2011       08-28-2012, 9:36 PM Reply   
Yes, it's flat. With the 1433 prop there is only about 3/8" clearance, so the plate can't be too thick.


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

All times are GMT -7. The time now is 1:41 AM.

Home   Articles   Pics/Video   Gear   Wake 101   Events   Community   Forums   Classifieds   Contests   Shop   Search
Wake World Home


© 2016 eWake, Inc.    
Advertise    |    Contact    |    Terms of Use    |    Privacy Policy    |    Report Abuse    |    Conduct    |    About Us