Articles
   
       
Pics/Video
       
Wake 101
   
       
       
Shop
Search
 
 
 
 
 
Home   Articles   Pics/Video   Gear   Wake 101   Events   Community   Forums   Classifieds   Contests   Shop   Search
WakeWorld Home
Email Password
Go Back   WakeWorld > Boats, Accessories & Tow Vehicles

Share 
Reply
 
Thread Tools Display Modes
Old     (boardman74)      Join Date: Jul 2012       02-04-2018, 1:17 PM Reply   
I am looking for idea's for a decent 6 channel amp. This is for my cruiser and I'm not looking to spend Wet Sounds type money. I plan to run 6-6.5 Kicker 43KM654LCW which are rated at 65 RMS and 195 peak 4 ohms. I'd like to drive them close to the 65RMS.

Only option I have found is the kicker 450.6. But I don't like that it lists power at 75x6 at 2 ohms. I plan to have just one speaker per channel so @ 4 ohm. Doesn't list power for 4 ohm. Anyone have any cause what rated power is at 4 ohms?

Does not have to be a marine amp as it will be mounted inside the cabin.

Ideas??
Old     (onlyinboards)      Join Date: Oct 2014       02-04-2018, 1:28 PM Reply   
Roswell has a 900.6 Amp that is new in their lineup. List price is $595 but i could probably get you a deal on one. Not sure what you were looking to spend.
Old     (boardman74)      Join Date: Jul 2012       02-04-2018, 1:45 PM Reply   
Less than that...

Looking more in the under $400 range. WS HTX6 is $579.....
Old     (chpthril)      Join Date: Oct 2007       02-04-2018, 5:21 PM Reply   
Is there are particular reason you need to run 6 x 4 ohm? The new Kicker 450.6 delivers 40W rms x 4 ohm. I would not get too hung up on RMS. If you want to really push them to their potential, you need to look for an amp thats 4 ohm rms is well north of 100W. If you are not looking to drive the snot out of them, 50W rms or more to a speaker is fine. Basically, id want a quality wattage over cheap wattage.
Old     (boardman74)      Join Date: Jul 2012       02-04-2018, 8:30 PM Reply   
Nope. I just bought longevity wise it was always better to run an amp at 4 ohms. Just figured 6 speakers to run, that a 6 channel would be best. If there is another better option I am certainly open to it.

I plan to run the 6 kicker 6.5 in boats and a single 12 inch sub. Really would like that to be off 2 amps.
Old     (soonerbilly)      Join Date: Jul 2013       02-05-2018, 8:49 AM Reply   
So then why not go a 5 channel and a smaller 2 channel. Unless youre gonna have the need for the sub to be over 500. Lots of options at that point.
Old     (soonerbilly)      Join Date: Jul 2013       02-05-2018, 8:54 AM Reply   
I had a Memphis prx 5.550 50 x 4 and 300 x1 in my sons jeep......think I got it onsale for around 200. Its not the best amp but it was pretty decent has some decent adjustability and a separate bass knob.
Old     (chpthril)      Join Date: Oct 2007       02-05-2018, 9:23 AM Reply   
As long as you do not need 3 zone volume control, then consider a 4 chnl marine amp. No issue at all for a quality marine 4 chnl amp to drive 3 pair of 4 ohm speakers. What you might think you gain in longevity by running a very budget friendly 6 chnl in 4 ohm x 6, you can very well lose in build quality. Whats to say that price-point 6 chnl has more heat sink and a more robust power supply, then the better built marine 4 chnl. Ill take 50 quality watts over 100 cheap watts any day.

With a sub coming into the equation, you might be able to spread out your budget by going with a 4 or 6 chnl amp that can drive your 6 in-boats and woofer. So now a $600 HTX-6 marine 6 chnl isnt looking to bad. Or even the Syn-DX6 for a higher output system with 100W rms for each speaker and 600W for a woofer. one amp to wire and install over two can same some time and cost on incidentals.

For a boat that lives on the water, ID suggest a marine amp.
Old     (boardman74)      Join Date: Jul 2012       02-05-2018, 5:29 PM Reply   
Please excuse my ignorance and the dumb questions I am going to ask. Part of the reason I wanted to run 6 speakers to a 6 channel amp is I am comfortable with that and know how to wire it.

So say I bought a HTX-6. Its rated 150x6 2 ohm stereo. Also 3x300 4 ohm mono (bridged). So can I run channels 1-4 2 ohm stereo with 2 speakers per channel for a 2 ohm load, them bridge channel 5-6 with a 4 ohm sub running 4 ohm mono for 300 watts.

So to get a 2 ohm load I just wire 2 speakers into 1 channel on the amp? Both positives into the positive terminal and both negatives into the negative? Then each speaker will see 75 watts? So then I have 2 speakers in channel 1, channel 2, and channel 3. Then channel 4 is empty. Then the sub in channel 5-6 bridged?

Is my logic correct or can't the amp be split like that?
Old     (chpthril)      Join Date: Oct 2007       02-05-2018, 5:49 PM Reply   
Real close. Beak it down as a 4 chnl amp and 2 chnl amp. Bridged 4 ohm woofer = 300W, you got that.

For 1-4, I would put one pair on say chnls 1 and 2 @ 4 ohm stereo. And then one pair on 3 @ 2 ohm then last pair on 4 @ 2 ohm. Set gains accordingly.
Old     (Stokes760)      Join Date: Jun 2017       02-05-2018, 8:10 PM Reply   
Ive been haveing good luck with rockville amps in budget systems.
Old     (Tallredrider)      Join Date: Mar 2011       02-05-2018, 9:36 PM Reply   
I've got a used Arc KS 900.6 that works perfectly. It would seem to be perfect for what you need. Send me a PM on the Tige owners forum if you are interested (Talltigeguy).

Reply
Share 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On



All times are GMT -7. The time now is 5:22 PM.

Home   Articles   Pics/Video   Gear   Wake 101   Events   Community   Forums   Classifieds   Contests   Shop   Search
Wake World Home

 

© 2016 eWake, Inc.    
Advertise    |    Contact    |    Terms of Use    |    Privacy Policy    |    Report Abuse    |    Conduct    |    About Us