Articles
   
       
       
Pics/Video
   
       
       
Shop
Search
 
 
 
 
 
Home   Articles   Pics/Video   Gear   Wake 101   Events   Community   Forums   Classifieds   Contests   Shop   Search
WAKE WORLD HOME
Email Password
Go Back   WakeWorld > >> Boats, Accessories & Tow Vehicles Archive > Archive through June 17, 2007

Share 
Reply
 
Thread Tools Display Modes
Old    Scar13 (scar13)      Join Date: Jul 2005       06-07-2007, 8:56 AM Reply   
My rubber on my Platform is junk! It basicly gets black mess all inthe baot so I ordered me some gator grip.

Question is how do I remvoe the rubber and the glue?
Old    Sam (wake1823)      Join Date: Dec 2005       06-07-2007, 9:05 AM Reply   
powerwash it off.

it is a pain in the ass , be prepared to spend alot of time on it.
Old    David Bell (dabell)      Join Date: Apr 2007       06-07-2007, 9:16 AM Reply   
1) Peel the mating off and if it gives you a problem, use a hair-dryer with the heat on.
2) GluGone for the glue along with a PLASTIC putty knife

A LOT of scrubbing will be required. Good luck.
Old    Rudy Fierros (vfrdude)      Join Date: Aug 2006       06-07-2007, 9:39 AM Reply   
I just finished doing this - the material itself will come off fairly easily, but will leave a thick layer of adhesive. Using a heat gun, and a 2 in putty knife.I used a metal one, it didn't scrach anything. It's going to be covered anyway. Heat the adhesive and just peel it right off. There will be a glue residue. This can be taken off using some acetone.

I would advise against using any adhesive remover. I left it on too long, and it lifted the gel coat up in a few spots. I ended up spending a few days fixing this before I was able to get the new pad on....

I ended up going with Hydro-Turf Molded Diamond in black. The original pad on my Outback LS was looking pretty bad.




Upload
Upload
Old    David Bell (dabell)      Join Date: Apr 2007       06-07-2007, 9:47 AM Reply   
Op, to add to Rudy's list of to do's.

Use the previous mating for a template for the new mating.

FYI, nice call Rudy.....
Old    Rudy Fierros (vfrdude)      Join Date: Aug 2006       06-07-2007, 10:36 AM Reply   
In my case, the material didn't come up in one piece. I'm lucky that my neighbor is a carpet layer, and he pretty much handled getting the new material cut right. I used dimensions from a new Moomba's ski platform for the center section. The Hydro-Turf sheets aren't long enough to cover in one piece.
Old    David Bell (dabell)      Join Date: Apr 2007       06-07-2007, 10:56 AM Reply   
Off Topic

Rudy: how is the HydroTurf working for you? How is the durability of it. I have some samples at home but still thinking about Gator Grip or HydroTurf.....
Old    Rudy Fierros (vfrdude)      Join Date: Aug 2006       06-07-2007, 11:22 AM Reply   
I just finished installing it. Haven't had a chance to get it out, and use it. When I do, I'll be sure to let everyone know how it's working out.

There was a thread about Supra swim platform residue, and the Hydro-Truf and Gator grip both received positive comments.

http://www.wakeworld.com/MB/Discus/messages/3183/446833.html
Old    Scar13 (scar13)      Join Date: Jul 2005       06-07-2007, 11:28 AM Reply   
Hmm I see people saying use glugone then I see people say dont use adhesive remover then use acetone?

ARGHH HA!

So a little acetone shoudlnt hurt it right?
Old    David Bell (dabell)      Join Date: Apr 2007       06-07-2007, 11:34 AM Reply   
I would suggest you do small sections and not all at one time.
Old    Rudy Fierros (vfrdude)      Join Date: Aug 2006       06-07-2007, 11:53 AM Reply   
When I messed up my gel coat, I went to talk with the guys at Pro Fiberglass and Gel coat repair in Livermore.
http://www.profiberglass.com/



They said acetone will not harm the gel coat. Use the heat gun with a putty knife, then use acetone to get the small amount of adhesive residue off the surface.

(Message edited by vfrdude on June 07, 2007)
Old    Scar13 (scar13)      Join Date: Jul 2005       06-08-2007, 7:23 AM Reply   
Ok got it done and it was super simple!

one heat gun super heat everything and it pulsl right off and removed 99% of the glue and adhesive.

Any left I used a little green scouring pad and a heat gun and it came right up!
Old    Rudy Fierros (vfrdude)      Join Date: Aug 2006       06-08-2007, 9:05 AM Reply   
Cool- If I would have used a heat gun in the first place, I could have had the whole project completed in a few hours. INstead I spent a couple of days fixing the gel coat that had lifted from using the adhesive remover....
Old    Richard (nauty)      Join Date: Feb 2004       06-11-2007, 1:04 PM Reply   
I did mine a few months ago. I talked to the folks at Skiers Choice and here's what they told me to do in order to get the adhesive off:

1) Peel off old mats
2) Spray platform down with WD-40 and leave on for 40 mins.
3) Scrape off residue with plastic putty knife.
4) Clean off WD-40 with Acetone (apply and immediately wipe off).

This worked like a charm.
Old    WakesetterLSV (closedtoe)      Join Date: Jan 2007       06-11-2007, 4:39 PM Reply   
why are you taking it off?
Old    JHG (jhgsupra)      Join Date: Mar 2006       06-12-2007, 3:19 AM Reply   
I'm next! I've had enough with the black residue getting all over my upholstery. There are toe prints everywhere. How much diamond plating should I expect to need and estimate on the cost? Thanks for all the advise...
Old    JHG (jhgsupra)      Join Date: Mar 2006       06-13-2007, 3:13 AM Reply   
Rudy Fierros (vfrdude),

How's the hydro-turf holding up? I see you have black which Hydro-turf said they wouldn't have until July. Thanks,

JHG

Reply
Share 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On



All times are GMT -7. The time now is 8:01 PM.

Home   Articles   Pics/Video   Gear   Wake 101   Events   Community   Forums   Classifieds   Contests   Shop   Search
Wake World Home

 

© 2012 eWake, Inc.    
Advertise    |    Contact    |    Terms of Use    |    Privacy Policy    |    Report Abuse    |    Conduct    |    About Us