Articles
   
       
       
Pics/Video
   
       
       
Shop
Search
 
 
 
 
 
Home   Articles   Pics/Video   Gear   Wake 101   Events   Community   Forums   Classifieds   Contests   Shop   Search
WAKE WORLD HOME
Email Password
Go Back   WakeWorld > >> Boats, Accessories & Tow Vehicles Archive > Archive through March 15, 2005

Share 
Reply
 
Thread Tools Display Modes
Old    waterdog2            01-26-2005, 8:21 PM Reply   
I need to alter my bimini top to fit a new tower. The pipe fit's perfect in a 3/4 " electrician's pipe bender. Past experience trying to bend copper tubeing with same bender produced cracks. Will the aluminum pipe crack ? And does anyone know where to get a coupling to fit the same tubeing, Taco doesent make one. Any help is greatly apreciated
Old    Andrew (drewsy)      Join Date: Mar 2003       01-26-2005, 9:05 PM Reply   
Try filling the tube with sand & then start the bending process.
Old    sydwayz (sydwayz)      Join Date: Mar 2003       01-26-2005, 9:07 PM Reply   
Aluminum shouldn't crack, not as brittle as copper. Use alot of foot pressure when bending, helps with not kinking the pipe. And you can make a sleeve to fit inside the pipe and secure it with screws. Welding it would be best.
Old    Bill Bierbower (monstertower)      Join Date: Mar 2003       01-26-2005, 9:22 PM Reply   
You should be fine, your likely only changing a bend a little
Old    Mikeski (mikeski)      Join Date: Aug 2003       01-26-2005, 10:28 PM Reply   
I modified my old bimini to fit under my monster tower. I cut about 8" out of the center and narrowed the bows. I found aluminum tubing at the local Orchard supply hardware that fits perfectly inside the 3/4 aluminum tubes. I just used some screws to secure the pipe joints. If you can't find any I still have a section that I can send you. I did use my electricians bender to add a little more bend to the bows as well. Since I was only adding about 5 degrees I didn't need to worry about flat spots. (having lots of pipe bending experience as an electrician didn't hurt either)

Send me a note if you need my left over inside sleeve.
Old    Trace (trace)      Join Date: Feb 2002       01-27-2005, 6:42 AM Reply   
the conduit bender will definitely work, and aluminum bends well. the only thing that may happpen is the anodizing can crack if it's bent too much.
Old    waterdog2            01-27-2005, 5:56 PM Reply   
Thank's for everyones help. I still have a month or two before I actually have to do it, but it's nice to be fore warned of problems.
Monster, You called it before about the bimini not fitting, so you can say, I TOLD YOU SO. Im sort of wishing I would have went with the monster for certain reasons. But brand X look's pretty good on my boat and is pretty stiff, I just hate the feet and there instructions really sucked. I got there 05 model and I think they were still working out the instructions. I think ill go with the monster racks. Thank's again everyone.

Reply
Share 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On



All times are GMT -7. The time now is 12:38 PM.

Home   Articles   Pics/Video   Gear   Wake 101   Events   Community   Forums   Classifieds   Contests   Shop   Search
Wake World Home

 

© 2012 eWake, Inc.    
Advertise    |    Contact    |    Terms of Use    |    Privacy Policy    |    Report Abuse    |    Conduct    |    About Us