Articles
   
       
       
Pics/Video
   
       
       
Shop
Search
 
 
 
 
 
Home   Articles   Pics/Video   Gear   Wake 101   Events   Community   Forums   Classifieds   Contests   Shop   Search
WAKE WORLD HOME
Email Password
Go Back   WakeWorld > >> Boats, Accessories & Tow Vehicles Archive > Archive through July 28, 2009

Share 
Reply
 
Thread Tools Display Modes
Old    mike (shoulin)      Join Date: Aug 2005       07-02-2009, 10:01 AM Reply   
Hey guys i have an 04 mastercraft with the trailer that comes with the boat its a dual axle and one of the oil baths has turned white and the wheel gets really hot when i trailer, the dealer told me to take the tire off and that it would work fine as a quasi single axle trailer.

Does anyone have experience with this, will it work or is it bad for the trailer, I'm afraid I will do more damage trailering it to even get fixed, It gets extremely hot just going less than 5mins.

Any tips advice would be greatly appreciated, Hope everyone gets some waking in this weekend!
Old    Brett Yates (polarbill)      Join Date: Jun 2003       07-02-2009, 10:09 AM Reply   
It will work temporarily while you get the bearings, races and seal replaced. Not sure why you would do it other than to just take it to someone to get that fixed???
Old    mike (shoulin)      Join Date: Aug 2005       07-02-2009, 10:10 AM Reply   
Hey Brett

I know its an easy fix but with work I havent had a chance to get into the dealership and I want to go wakeboarding this weekend,

So it will be okay?
Old    Brett Yates (polarbill)      Join Date: Jun 2003       07-02-2009, 10:15 AM Reply   
What boat do you have and do you know what the mastercraft axles are rated at, weight wise? If it is a somewhat short drive to the lake then I think you will be ok. Is it on the front or rear axle. If it is on the front you will have more tongue weight. Do you have a full size truck?
Old    mike (shoulin)      Join Date: Aug 2005       07-02-2009, 10:18 AM Reply   
Brett,

04 x2 small boat

Yeah I have an f250, its on the front axle, dont know the weight but they sell single axle trailers with the boats so the they should be good to go, or that is my thought?

real short drive 5-8mins

My main question is what is the smarter move let it get hot or remove?

Thanks for the help

Mike

(Message edited by shoulin on July 02, 2009)
Old    Buzz (buzz_grande)      Join Date: Mar 2004       07-02-2009, 10:19 AM Reply   
Also are there brakes on that axle that you want to take the wheel off of? Some trailers have brakes on both axles, and some only on the front one. Would not want to drive any distance with brakes only on one wheel.

I had a flat on a Shasta trip, pulled off the flat one and drove a few miles to a tire store. Many have done this before. No problem. (VLX on an Extreme trailer).
Old    Flux (flux)      Join Date: Jun 2003       07-02-2009, 10:26 AM Reply   
If I am thinking correctly, the MC trailers have the torsion springs, not the typical leaf spring setup. On my leaf spring setup, I would downright scared that the hub might hit the ground and scrape. Heard it said you can chain the axle to the trailer frame so it won't bottom out if you have to run without a tire and rim.

At least check it first by removing the rim and removing the jack to see how close the hub get's to the ground. If it's the brake axle, be careful because the rotor is even bigger in diameter. I'd also consider disengaging the brakes if it's single axle and you are gonna lose one side.

DRIVE SLOW. Good luck and happy 4th.
Old    Brett Yates (polarbill)      Join Date: Jun 2003       07-02-2009, 10:27 AM Reply   
For that kind of distance with an f250 just take it off. If the bearing are shot and they get hot there is a possibility of causing damage to the axle.

Buzz may have brought up a good point on the brakes though. I don't think it should matter too much though. I don't think you can mess up the brakes just having them on one side. the only problem is maybe it pulls to one side when you slow down. Crap, with that boat and an F250 I would just put in the lockout tool for the brakes and not use them at all. Just give yourself a little more room behind the car in front of you.
Old    Jarod Craig (wake26)      Join Date: Mar 2009       07-02-2009, 10:28 AM Reply   
i think that the smarter move is to take it off and get it fixed before you trailer it. but if you have to I would take the tire off because the bearing are most likely shot and if you keep on driving it you could ruin the bearing races then you would be looking at replacing the whole hub rather then the bearings. do you know if it is the bearings or does it just need greased? does that axle have brakes on it are the brakes dragging?
Old    Kevin K (supra)      Join Date: Aug 2002       07-02-2009, 10:31 AM Reply   
I drove a boat for over 3 hours at 55 mph in an emergency situation with 3 tires, with no damage or no issues, 5-8 miles ( no problem) imo

(Message edited by supra on July 02, 2009)
Old    mike (shoulin)      Join Date: Aug 2005       07-02-2009, 10:34 AM Reply   
If I could squirt some grease in it I think it would be okay its just all white for whatever reason,

Yeah to trailer to dealer is at least 30 mins away so either way im screwed im just worried Im gonna really f something up and instead of under 200$ to fix its going to be a lot more, Im going to check with the dealer again and then take it off and get it fixed soon, Thanks for the help

Yeah don't know about the brakes?
Old    Brett Yates (polarbill)      Join Date: Jun 2003       07-02-2009, 10:40 AM Reply   
Damn, $200 for that is kind of ridiculous. Bearings, races, seal and a boat buddy is only about $40 cost and For a mechanic it shouldn't take more than 30 minutes to do this.
Old    Dustin (ncsumalibu)      Join Date: Mar 2009       07-02-2009, 10:42 AM Reply   
Get it fixed when you can but a short trip on three tires is not a problem.
Old    mike (shoulin)      Join Date: Aug 2005       07-02-2009, 10:51 AM Reply   
Cool thanks for the help guys I appreciate it,
Old    SEAN DEAN (05elitevc4)      Join Date: Jan 2008       07-02-2009, 12:22 PM Reply   
If you have leaf springs chain that end of the axle up to the frame while its on the ground with weight on it. Then jack it up and take the tire off. That way the axle rides close to the normal height going down the road. For that short of a trip I wouldnt sweat it.
Since you have a 250 I would disengage the brakes too.
Its not that hard of a fix though...get the parts and change them yourself. But if thats not an option you should be ok.
Old    266CrownlineBR (266crownlinebr)      Join Date: Apr 2007       07-06-2009, 9:16 PM Reply   
I have tied one of my axle's up with the tie down straps for my boat a couple of times. Had to drive 20 miles that way. Just tie it up and drive slow.
Old    Face Planter (mastercraft1995)      Join Date: Nov 2002       07-07-2009, 8:16 AM Reply   
Depending on the trailer you might not have to tie up the axle. My Extreme trailer I don't have to and I can drive all day on 3 tires.

Reply
Share 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On



All times are GMT -7. The time now is 5:06 AM.

Home   Articles   Pics/Video   Gear   Wake 101   Events   Community   Forums   Classifieds   Contests   Shop   Search
Wake World Home

 

© 2012 eWake, Inc.    
Advertise    |    Contact    |    Terms of Use    |    Privacy Policy    |    Report Abuse    |    Conduct    |    About Us