Articles
   
       
       
Pics/Video
   
       
       
Shop
Search
 
 
 
 
 
Home   Articles   Pics/Video   Gear   Wake 101   Events   Community   Forums   Classifieds   Contests   Shop   Search
WAKE WORLD HOME
Email Password
Go Back   WakeWorld > >> Boats, Accessories & Tow Vehicles Archive > Archive through June 08, 2008

Share 
Reply
 
Thread Tools Display Modes
Old    turbocivic5 (sscott0203)      Join Date: Sep 2007       05-10-2008, 10:11 AM Reply   
2 Wetsound Pro 80's
1 Kicker zx450.2

Specs of amp are:
Amplifier Class AB
Number of Channels 2
RMS Power (4 ohms) 150 watts x 2 channels
RMS Power (2 ohms) 225 watts x 2 channels
RMS Power (1 ohm) N/A
Bridged RMS Power 450 watts x 1 channel
Peak Power Output N/A
Minimum Impedance Unbridged 2 ohms
Minimum Impedance Bridged 4 ohms
THD at Rated RMS Power 1%
Speaker Level Inputs Yes
Preamp Outputs Yes - 1 pair
Built-in Crossover High-pass (HP), Low-pass (LP), Full (AP)
High-Pass Crossover Frequency 50 - 200 Hz
Low-Pass Crossover Frequency 50 - 200 Hz
Subsonic Filter N/A
Signal-to-Noise Ratio 95 dB
Channel Separation N/A
Bass Boost 0 - 18 dB
Bass/Gain Remote Yes
Fan Cooled No
Fuse Rating 30A x 2


Do i bridge these to get my amp at two ohms or what? Please be detailed its been awhile since i worker with audio.

One more question I have a kicker 4 channel running my six cabin speakers. I have it hooked up like this

2 Front speakers + - + - Thats on 2 channels of the amp. Rear ++ -- ++ -- is on the other two channels. That sound right?
Old    Nu Bu (05mobiuslsv)      Join Date: Apr 2006       05-10-2008, 10:53 AM Reply   
You can't make that amp run at 2 ohms with those speakers, you would have to get another set to do that. The speakers are 4 ohms, if you wired the speakers together you could only run them on one channel of that amp to get 2 ohms. Unfortunately you can't bridge those speakers to that amp, it's not stable at 2 ohms in bridged mode. If you haven't used that amp yet you could take it back and get a bigger model. I'm guessing you're trying to get the most out of the amp possible. Just try hooking it up with one Pro-80 on each side of that amp. Kickers are good about producing much more power than stated, so you're probably looking at more like 175X2 at 4 ohms at the end of the day.

Your kicker 4 channel for the cabin speakers is wired correctly. The 2 rear channels on the amp are wired at 2 ohms just to give you an idea what that looks like.
Old    TigeMike (chpthril)      Join Date: Oct 2007       05-10-2008, 12:10 PM Reply   
Like Nu Bu said, you cant bridge a 2ohm (2 4ohm speakers wired parallel) load, the amp will see a 1ohm load... not good for it.

Pro80's need at least 200W RMS and are 4ohm
Kicker ZX450.2 is 150W RMS x 2 @ 4ohm. This will leave the 80's a bit under powered. May look @ the ZX550.2 (205W @ 4ohm) or even better, the ZX850.2 (295W @ 4ohm).
Old    Hate N Pain (hatepain)      Join Date: Aug 2006       05-10-2008, 12:12 PM Reply   
Second nubu on this one just run it at 4 ohms it should have plenty of power and be nice and clean.
Old    Nu Bu (05mobiuslsv)      Join Date: Apr 2006       05-10-2008, 5:50 PM Reply   
Here's a great place for refurb kicker stuff. Comes straight from kicker with warranty. Hey mike how do you get 1 ohm out of 2 - 4 ohm speakers .

http://search.ubid.com/search/search.aspx
Old    Steve Amestoy (stevev210)      Join Date: Feb 2005       05-11-2008, 11:21 AM Reply   
Seth, I run a pair of Pro80's with a JLA4300, 150watts rms X2 at 4ohms and there as loud and clear as youll need. Im sure your kicker amp will be fine.
Old    Brit Rider (brit_rider)      Join Date: May 2004       05-11-2008, 2:11 PM Reply   
I've also run these speakers with 160 watts and seen great results....

Don't worry about your amp, I think it'll do fine - at least try it out first - I don' think you'll be disappointed.

Reply
Share 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On



All times are GMT -7. The time now is 10:32 PM.

Home   Articles   Pics/Video   Gear   Wake 101   Events   Community   Forums   Classifieds   Contests   Shop   Search
Wake World Home

 

© 2012 eWake, Inc.    
Advertise    |    Contact    |    Terms of Use    |    Privacy Policy    |    Report Abuse    |    Conduct    |    About Us