WakeWorld

WakeWorld (http://www.wakeworld.com/forum/index.php)
-   Archive through March 19, 2004 (http://www.wakeworld.com/forum/forumdisplay.php?f=105171)
-   -   Getting rid of stickers on board... HOW? (http://www.wakeworld.com/forum/showthread.php?t=103467)

herbilizer 03-14-2004 7:06 PM

I just bought a used board, but there are some stickers on it which I would like to remove... any ideas??? <BR> <BR>Any help is appreciated. Thanks. <BR>

cmm83 03-14-2004 7:17 PM

If you were real careful with a razor blade you could probably get them off without hurting the board. Use some goo gone if there was stickiness left over (I dont think that would hurt the board?) <BR>Hopefully the sun hasn't faded the board too much or else the stickers will still show even when they are gone.

sk8joe01 03-14-2004 7:21 PM

duct tape. peel the stickers, and then attack the sticky residue with the sticky side of duct tape. works like a dream.

ryin 03-14-2004 7:42 PM

ya use the razor blade real careful to get under the sticker. you can also rub some lighter fluid over any sticker crap still left on the board.

aidan 03-14-2004 7:47 PM

Use hairdryer to heat up stickers and then peel. Use Lift-Off from homedepot to remove all adhesive without dis-coloring board. <BR> <BR>(Message edited by Aidan on March 14, 2004)

solo 03-14-2004 8:04 PM

Hair dryer and WD40.

grampawakerider 03-14-2004 8:20 PM

Herbert... <BR>Glad to see you got the board ok. Hairdryer idea sounds best to me. After that, there is a product called "goof off" that works pretty killer on the leftover residue. I don't know if they have it over in Hong Kong though.

herbilizer 03-14-2004 8:29 PM

Thanks for all the idea guys... time for a before and after pic for future references...

malibuboarder75 03-14-2004 8:30 PM

i peal the stickers off with my hand. normally some residue will remain which u can take off with paint thinner.

leshella 03-14-2004 8:33 PM

NO NO NO! just soak your board in HOT water (like in the tub) and then just rub them off--easy as anything.

cramey 03-14-2004 8:47 PM

just break the thing off a huge double up, and return it to the mfg for a spiffy new one... works for me every time.

tpanoz 03-14-2004 9:01 PM

heat gun then peel them off and use some goo-gone to get rid of the residue

solo 03-14-2004 10:54 PM

Hair dryer and WD40.

mx21 03-15-2004 3:36 AM

Hair dryer and WD40. <BR> <BR> -- I second. Works every time. But I would add Hair dryer THEN WD40 (to remove residue). Gotta be careful - the least common denominator is out there somewhere spraying WD40 into their hairdryer.

jonb 03-15-2004 7:23 AM

nailpolish remover works for the sticky stuff too.

jetgofish 03-15-2004 3:33 PM

Try using Goof Off!

gunz 03-15-2004 3:47 PM

Goof Off will eat the laminate!It happened to my old board.I like the WD40 idea.

wes_can_riders 03-15-2004 4:36 PM

vinger and water works good to get rid of the crap left over or paint thinner even better

turtle 03-15-2004 4:43 PM

Solo wins it

herbilizer 03-15-2004 5:58 PM

I ended up using hair dryer and wd40 for the goo left... and it's fine now... just like new. <BR> <BR>Thanks for the advice, everyone!!!

solo 03-15-2004 7:18 PM

Told you....<img src="http://www.wakeworld.com/MB/Discus/clipart/wink.gif" border=0>


All times are GMT -7. The time now is 10:37 PM.