2008 Malibu VLX Window Tint Question
Hey Guys,
Family has a 2008 Malibu VLX and we were thinking about getting the windows tinted. I contacted a local shop and they quoted me $300 to tint leaving the window on OR $450 to removed the window and tint it. They said that there will be a 1/8 gap near the seal. Do you guys have pictures of the tint leaving the windows on, is there a gap? Thanks guys! |
1 Attachment(s)
I had my window tinted on my 05 VLX and they did it with the windows still on and there is not on gap to be seen. It may depend on each person that tints windows but mine is very clean looking One of the best mods I ever did to the boat and will have it on any other boat that I buy.
|
awesome. what percentage is yours?
|
No pictures offhand but we had our boat done and the windows weren't removed and there was no gap.
|
Can anyone recommend a place Near Manteca, CA
|
Because you can't always get a S.S. blade at a right angle at the base of the entire glass interior because of the dash elevation it can be hard to get complete access to trim the film perfectly at the bottom. Some may cut into the rubber gasket as a cure and some may leave a very slight gap at the bottom in order to stay away from the rubber gasket edge. So don't get too hung up on just that singular detail. Ask each individual tint shop how they manage this challenge. Maybe they have a better solution and maybe they cut into the gasket a little. Maybe the gap is much finer than 1/8" and given the alternative you may want to go that route. But if you don't get a reasonable answer I would move on.
Its much harder to release the film liner, exposing the adhesive and keep contamination down in an open boat application versus a somewhat closed cabin of a vehicle. Any airborne debris will be permanently entombed behind the film. So sometimes removing the windshield could be more about applying the film in a cleaner, controlled environment. Since film on a boat is far less shaded than in a hardtop vehicle and is always equally lit from the interior side, all film will appear much lighter on a boat. A 20 percent film on a boat will appear equal to a 35 percent film on a typical vehicle side window. Going any darker than 20 percent light transmittance is very dangerous at night or even at dusk because it impedes your vision. The prices quoted certainly sound good if the film is high quality and the job is clean. Prices will vary by a large margin depending on whether the film is strictly dyed, uses a metal matrix or is ceramic glass particle. Know what particular grade you are getting. Just a few window film considerations for you. David Earmark Marine |
Here is a 2011 VLX that I had done by a local shop for a customer. We did 20%. It looked killer on the boat and was perfect for during the day. At dusk, it was about as dark as I would like to go myself. It was done with the windows in place. The installer laid the film on the outside and trimmed it to fit, then prep'd the inside of the glass and applied. It came out real clean. Their only concern was the dot-matrix looking border. They say that the film can sometimes come loose after time.
http://i181.photobucket.com/albums/x...l/P5270282.jpg http://i181.photobucket.com/albums/x...l/P5270281.jpg http://i181.photobucket.com/albums/x...l/P5270280.jpg |
I've Been thinking of getting my VLX tinted as well. But was wondering of doing a mirror chrome silver or what ever you call it tint instead of black. Has anybody done that?
|
I think with the way the sun hits the windshields on our boats going the mirror chrome is a BAD idea. I feel like it would cause you to blind other boaters when the sun hits it at the right angle.
|
2 Attachment(s)
Quote:
He did my 2008 Supra (with one piece front window) and 2011 Malibu VLX. ACME Stereo 6430 Franklin Blvd Sacramento, CA 95823 (916) 429-2293 For comparison, here is my Supra with 35%, Malibu has 20% on it... after having both would recommend going 20%, cuts down on the glare and I think it looks better. However, you will be looking over windshield on a late evening on the water with 20%. |
Quote:
|
I have had it done twice to my boats. Never had the windshield removed and never had a gap, i think you just need to find an installer who will take his time on it. I went with 20% the first time (black boat) and wanted something a little darker so the next boat (red boat) had 5%. Never had any problems with glare.
http://i127.photobucket.com/albums/p...-11Sync232.jpg http://i127.photobucket.com/albums/p...-11Sync266.jpg |
Those windshields that are split in the forward corners are friendly while the single piece windshields with those compound curves in the front corners are really tough.
There are alot of very good automotive film techs that do not have a handle on boats. Just make sure you find one that has real boat experience. David Earmark Marine |
Quote:
|
Travis, the tint job on your supra would be similar to my malibu. did you have them take off the window?
|
Quote:
If you contact Ben he will know what needs to be done, he has done quite a few tint jobs on boats. |
I talked to Ben and he said that it's possible to do it on the boat but that 1/8 comes into factor.. but its also $150 cheaper.... i was just curious to how noticeable
it really is. |
Ben would not deliver a product that does not look good, or you could research removing the windows yourself on the Bu. I am sure if you goto the MalibuCrew website there will be someone who can answer this question for you. I would encourage you to remove the windows, then you will get 100% coverage.
|
All times are GMT -7. The time now is 11:50 AM. |